Name: Steinen Oil nozzle 0.60GPH / 60S
Brand: Steinen
SKU: 0.60GPH / 60S

Flow rate

0.6 GPH

Spray angle

60 °

Spray pattern

Choose a nozzle by its marks

Nozzles of different brands interchange when the marks match: Flow rate, Spray angle, Spray pattern. Set them as on the old nozzle — below are the ones that fit, with price and stock.

Description

The Steinen Oil nozzle 0.60GPH / 60S is an oil nozzle with a flow rate of 0.6 GPH, a 60 ° spray angle, and an S spray pattern. It is used to atomise fuel oil in a burner, forming the spray that is mixed with air and ignited. The 0.6 GPH rating defines the volume of oil passed per hour at the nozzle's rated pressure. The 60 ° angle sets the width of the spray cone, and the S pattern denotes the shape of the spray. It is a replacement part for oil-fired burners and boilers that take this nozzle specification.

Nozzle selection chart

Flow rate	kg/h	45°	60°	80°
0.40	1.27		ST
0.45	1.43		ST
0.50	1.59		ST
0.55	1.75		ST
0.60	1.91		S ST
0.65	2.07		S
0.75	2.38		S
0.85	2.70		S
1.00	3.18		H S	S
1.10	3.50		S
1.20	3.82		S
1.25	3.97		S
1.35	4.29		S
1.50	4.77		S
1.65	5.25		S
1.75	5.56	S	S
2.00	6.36	S	S
2.25	7.15	S	S
2.50	7.95		S
2.75	8.74		S
3.00	9.54		S
3.50	11.13		S
4.00	12.72		S
4.50	14.31	SS	SS
5.00	15.90	SS	SS
5.50	17.49	SS	SS
6.00	19.08	SS	SS	SS
6.50	20.67	SS	SS
7.00	22.26	SS	SS
7.50	23.85	SS	SS
8.00	25.44	SS	SS
8.50	27.02			SS
9.00	28.61	SS	SS	SS
10.00	31.79	SS	SS	SS
11.00	34.97	SS	SS
12.00	38.15	SS	SS
13.00	41.33	SS	SS
14.00	44.51	SS	SS
15.00	47.69	SS	SS
16.00	50.87	SS	SS
17.00	54.05	SS	SS
18.00	57.23	SS	SS
20.00	63.59	SS	SS
22.00	69.95	SS	SS
24.00	76.31	SS	SS
26.00	82.66	SS	SS
28.00	89.02	SS
30.00	95.38	SS

Choosing and fitting

Oil nozzles of this type are selected by matching the flow rate, spray angle, and spray pattern to the burner manufacturer's specification. The mounting form must also match: the nozzle body, thread, and seat must fit the nozzle holder or adapter on the burner. Before ordering, compare the markings on the old nozzle and the burner data plate with the required flow rate, angle, and pattern. The pump pressure the burner is set to must correspond to the rated flow of the nozzle.

Signs of failure

Oil nozzles of this kind can clog, wear at the orifice, or develop a distorted spray pattern over time. When this happens, the burner may run rough, produce smoke, fail to ignite reliably, or show a changed flame shape. A blocked or worn nozzle can also cause pulsation or a drop in heat output. Check the nozzle for blockage, damage, and spray pattern, and compare the flame and combustion readings against the burner settings.