Name: Steinen Oil nozzle 1.65GPH / 60S
Brand: Steinen
SKU: 1.65GPH / 60S

Flow rate

1.65 GPH

Spray angle

60 °

Spray pattern

Choose a nozzle by its marks

Nozzles of different brands interchange when the marks match: Flow rate, Spray angle, Spray pattern. Set them as on the old nozzle — below are the ones that fit, with price and stock.

Description

The Steinen 1.65GPH / 60S is an oil nozzle for pressure-jet oil burners. It meters fuel at a flow rate of 1.65 GPH and delivers it in an S spray pattern at a 60 ° spray angle. The nozzle atomises the oil into a cone-shaped spray that mixes with combustion air at the burner head. It is identified by the SKU 1.65GPH / 60S.

Nozzle selection chart

Flow rate	kg/h	45°	60°	80°
0.40	1.27		ST
0.45	1.43		ST
0.50	1.59		ST
0.55	1.75		ST
0.60	1.91		S ST
0.65	2.07		S
0.75	2.38		S
0.85	2.70		S
1.00	3.18		H S	S
1.10	3.50		S
1.20	3.82		S
1.25	3.97		S
1.35	4.29		S
1.50	4.77		S
1.65	5.25		S
1.75	5.56	S	S
2.00	6.36	S	S
2.25	7.15	S	S
2.50	7.95		S
2.75	8.74		S
3.00	9.54		S
3.50	11.13		S
4.00	12.72		S
4.50	14.31	SS	SS
5.00	15.90	SS	SS
5.50	17.49	SS	SS
6.00	19.08	SS	SS	SS
6.50	20.67	SS	SS
7.00	22.26	SS	SS
7.50	23.85	SS	SS
8.00	25.44	SS	SS
8.50	27.02			SS
9.00	28.61	SS	SS	SS
10.00	31.79	SS	SS	SS
11.00	34.97	SS	SS
12.00	38.15	SS	SS
13.00	41.33	SS	SS
14.00	44.51	SS	SS
15.00	47.69	SS	SS
16.00	50.87	SS	SS
17.00	54.05	SS	SS
18.00	57.23	SS	SS
20.00	63.59	SS	SS
22.00	69.95	SS	SS
24.00	76.31	SS	SS
26.00	82.66	SS	SS
28.00	89.02	SS
30.00	95.38	SS

Choosing and fitting

Nozzles of this type are selected by matching the flow rate, spray angle and spray pattern to the burner manufacturer's specification for the appliance. The mounting form must match the burner's nozzle adapter: the seat, thread and the length of the nozzle body have to correspond to the holder on the equipment. Before ordering, compare the markings on the old nozzle with the required values and check the nozzle adapter for damage or wear. The flow rate, angle and pattern stamped on the replacement must equal those of the nozzle being replaced.

Signs of failure

Nozzles of this kind commonly fail by clogging of the internal filter or the orifice, by wear of the orifice that increases flow, or by a distorted spray pattern from deposits or damage at the tip. On the equipment this appears as a smoky flame, unstable combustion, delayed ignition, pulsation or a failure to reach the required heat output. Check the nozzle strainer, the spray pattern and the electrode and burner head settings, and compare the nozzle markings with the specification before replacing.