Name: Danfoss Oil nozzle 1.75GPH,45S 030F4930
Brand: Danfoss
SKU: 030F4930

Flow rate

1.75 GPH

Spray angle

45 °

Spray pattern

Choose a nozzle by its marks

Nozzles of different brands interchange when the marks match: Flow rate, Spray angle, Spray pattern. Set them as on the old nozzle — below are the ones that fit, with price and stock.

Description

This is an oil nozzle with a flow rate of 1.75 GPH, a 45 ° spray angle and an S spray pattern. It is used to atomise fuel oil into a fine spray for combustion in an oil burner. The 45 ° angle defines the cone width of the spray leaving the nozzle. The S pattern denotes a solid spray cone. The nozzle is identified by SKU 030F4930.

Nozzle selection chart

Flow rate	kg/h	30°	45°	60°	80°
0.30	0.95			H S	H S
0.35	1.11			S	S
0.40	1.27		S	H S	H S
0.45	1.43		S	S	H S
0.50	1.59	S	S	H S	H S
0.55	1.75		S	H S	H S
0.60	1.91	S	H S	B H S	B H S
0.65	2.07		B S	B H S	B H S
0.75	2.38	S	B S	B H S	B H S SR
0.85	2.70	S	B H S	B H S SR	B H S
1.00	3.18	S	B S	B H S	B H S
1.10	3.50		S	H S	S
1.20	3.82		S	H S	S
1.25	3.97	S	B S	B H S	B H S
1.35	4.29		B S	B H S	B H S
1.50	4.77	S	B S	B H S	B H S
1.65	5.25		S	H S	H S
1.75	5.56	S	S	H S	S
2.00	6.36	S	B S	B H S	B H S
2.25	7.15	S	B S	B H S	S
2.50	7.95	S	B S	B H S	B S
2.75	8.74		B S	B H S	H S
3.00	9.54	S	B S	B H S	B H S
3.50	11.13		S	S	S
3.75	11.92		B	B	B
4.00	12.72		S	S	S
4.50	14.31		B S	B S	B S
5.00	15.90		B S	B S	B S
5.50	17.49		B S	B S	B S
6.00	19.08		B S	B S	B S
6.50	20.67		B	B	B
7.00	22.26			S
7.50	23.85		B	B	B
8.00	25.44			S
8.50	27.02		B	B	B
9.00	28.61			S
10.00	31.79		B	B	B
11.00	34.97		B	B	B
12.00	38.15		B	B	B
13.50	42.92		B	B	B
15.00	47.69		B	B	B
17.00	54.05			B	B
19.50	62.00			B	B
22.00	69.95		B	B	B
25.00	79.49			B	B
28.00	89.02			B	B
31.50	100.15		B	B	B
35.00	111.28		B

Choosing and fitting

Nozzles of this type are selected by matching the flow rate, spray angle and spray pattern to the burner manufacturer's specification. The mounting thread and the length of the nozzle body must match the nozzle holder on the burner. Before ordering, compare the markings on the old nozzle with the required values, and check that the seat and the electrode position are not disturbed during replacement.

Signs of failure

Nozzles of this kind can clog, wear at the orifice, or develop a distorted spray pattern. When this happens the burner may produce a smoky flame, fail to ignite, pulsate, or show a change in combustion readings. Check the nozzle for blockage or wear and compare the spray pattern with the specified angle and pattern.