Name: Danfoss Oil nozzle 15.00GPH,60B 030B0143
Brand: Danfoss
SKU: 030B0143

Flow rate

15 GPH

Spray angle

60 °

Spray pattern

Choose a nozzle by its marks

Nozzles of different brands interchange when the marks match: Flow rate, Spray angle, Spray pattern. Set them as on the old nozzle — below are the ones that fit, with price and stock.

Description

This is a Danfoss oil nozzle with a flow rate of 15 GPH, a 60° spray angle and a B spray pattern. It is used to atomise fuel oil into a fine spray so the burner can mix it with air and burn it. The 60° angle sets how wide the cone of oil is spread, and the B pattern defines the shape of that spray. The nozzle is identified by SKU 030B0143.

Nozzle selection chart

Flow rate	kg/h	30°	45°	60°	80°
0.30	0.95			H S	H S
0.35	1.11			S	S
0.40	1.27		S	H S	H S
0.45	1.43		S	S	H S
0.50	1.59	S	S	H S	H S
0.55	1.75		S	H S	H S
0.60	1.91	S	H S	B H S	B H S
0.65	2.07		B S	B H S	B H S
0.75	2.38	S	B S	B H S	B H S SR
0.85	2.70	S	B H S	B H S SR	B H S
1.00	3.18	S	B S	B H S	B H S
1.10	3.50		S	H S	S
1.20	3.82		S	H S	S
1.25	3.97	S	B S	B H S	B H S
1.35	4.29		B S	B H S	B H S
1.50	4.77	S	B S	B H S	B H S
1.65	5.25		S	H S	H S
1.75	5.56	S	S	H S	S
2.00	6.36	S	B S	B H S	B H S
2.25	7.15	S	B S	B H S	S
2.50	7.95	S	B S	B H S	B S
2.75	8.74		B S	B H S	H S
3.00	9.54	S	B S	B H S	B H S
3.50	11.13		S	S	S
3.75	11.92		B	B	B
4.00	12.72		S	S	S
4.50	14.31		B S	B S	B S
5.00	15.90		B S	B S	B S
5.50	17.49		B S	B S	B S
6.00	19.08		B S	B S	B S
6.50	20.67		B	B	B
7.00	22.26			S
7.50	23.85		B	B	B
8.00	25.44			S
8.50	27.02		B	B	B
9.00	28.61			S
10.00	31.79		B	B	B
11.00	34.97		B	B	B
12.00	38.15		B	B	B
13.50	42.92		B	B	B
15.00	47.69		B	B	B
17.00	54.05			B	B
19.50	62.00			B	B
22.00	69.95		B	B	B
25.00	79.49			B	B
28.00	89.02			B	B
31.50	100.15		B	B	B
35.00	111.28		B

Choosing and fitting

Nozzles of this type are selected by matching the flow rate, spray angle and spray pattern to the burner and combustion chamber, and by matching the thread and mounting form to the nozzle holder. Before ordering, compare the markings on the old nozzle and check the seat and thread in the holder for damage. The nozzle must sit squarely and seal on its seat, and the electrode position and blast tube must be set as specified for the burner.

Signs of failure

Nozzles of this kind usually fail by clogging, wear of the orifice or a damaged seat, which shows as a weak, distorted or pulsating flame, delayed ignition, soot, smoke or a rise in flue gas temperature. A blocked or worn nozzle can also cause the burner to lock out or run erratically. Check the flame shape, the nozzle strainer and the electrode settings, and replace the nozzle if the spray pattern or flow is visibly wrong.